[categoryname]

Trio Bracelet Project

Trio Bracelet Project
  • Trio Bracelet Project
B1055
1 Review(s)
5
 | Questions about how to use this item? Click here to ask a question

This project sponsored by:

  1. Cut the leather cording down to six 6-1/4" lengths or longer depending upon the size bracelet you want to make. Take one of the end caps and squeeze a couple of drops of Zap-a-Gap glue into the end, making sure to get the glue all around the inside of the end cap. Place the ends of the six lengths of leather cording into the glued end cap and allow to cure for at least 30mins before picking up to continue working.
  2. Cut the 1' wire in half. Measure about 1-7/8" up from the base of the end cap (where the cording comes out) and compress the cording with your fingers on your non-dominant hand. Place the end of the wire so that 1/4" of the wire is under your index finger on your non-dominant hand. Keep the wire parallel to the rest of the cording and begin to wrap the wire around all of the cording. Wrap about four times to secure, and then cut off the 1/4" wire with your side cutters where the coil starts. Cut the wire off on the other end of the coil as well, and then take your chain nose pliers and bend the coil ends slightly into the cording/coil combo just so that the ends won't get caught on your clothing or irritate your skin as you wear the bracelet.
  3. Thread on all of the twisted beads onto the cording in this order; gunmetal, antique brass, silver. After all beads are threaded on, slide them all the way to the coil on the cording. Now measure 3/8" up the cording from the last bead threaded on and make another coil with the wire the same way that you did on the other side of the bracelet. (make sure to tuck the ends of the coil in!)
  4. Take the remaining end cap and fill this with a few drops of Zap-a-Gap glue and then fit the ends of the six lengths of leather cording into this end cap. Allow it to sit for at least 30mins to cure (make sure that the loop on the end of this end cap faces the same direction as the other end cap on the other side of the bracelet)
  5. Open the two jump rings with your Chain and Round Nose pliers. Fit a jump ring onto each of the loops on the end caps and use this to then attach one half of the hook and eye clasp to each half of the bracelet. Make sure both jump rings are closed completely and you're done.

Quantity of Items Needed
QuantityItem
37-½ Inches1mm Leather Cord
1 Inch22ga Round Wire
58mm Antique Silver Plated Twisted Spacer Beads
58mm Antique Brass Plated Twisted Spacer Beads
58mm Antique Gunmetal Plated Twisted Spacer Beads
24mm End Caps
1Hook and Eye Clasp
24mm Jump Rings
Inspirational
This uses a lot of materials I don't normally use, so it's inspirational for future designs.
Did you find this helpful?  1 of 1 Found Helpful
Reviewed by:  from USA. on 3/29/2019
5/5
There are no reviews for this product!

Buy Project Components

TierraCast Twisted Spacer Bead 9x2mm Pewter Antique Silver Plated (1-Pc)
TierraCast Twisted Spacer Bead 9x2mm Pewter Antique Silver Plated (1-Pc)
$1.55
TierraCast Twisted Spacer Bead 9x2mm Pewter Oxidized Brass Plated (1-Pc)
TierraCast Twisted Spacer Bead 9x2mm Pewter Oxidized Brass Plated (1-Pc)
$1.54 $1.08
TierraCast Pewter Antique Gunmetal Plated Twisted Spacer Bead 8mm (1-Pc)
TierraCast Pewter Antique Gunmetal Plated Twisted Spacer Bead 8mm (1-Pc)
$0.77
End Cap 10x4mm Gold Plated (2-Pcs)
End Cap 10x4mm Gold Plated (2-Pcs)
$1.99
Hook and Eye Clasp 25x7mm Gold Plated (4-Sets)
Hook and Eye Clasp 25x7mm Gold Plated (4-Sets)
$0.99
Zap a Gap Glue 1/2oz
Zap a Gap Glue 1/2oz
$7.72
Open Round Jump Ring 4.5mm Gold Plated (100-Pcs)
Open Round Jump Ring 4.5mm Gold Plated (100-Pcs)
$3.10
Leather Cord Brown 1mm (25 Yards)
Leather Cord Brown 1mm (25 Yards)
$27.00
Brass Wire Round 22ga (20-Ft)
Brass Wire Round 22ga (20-Ft)
$5.99
     

Recently Viewed Items

Thank you for visiting www.jewelrysupply.com
Please visit us again for more great jewelry making supplies
Questions? Call us at (866) 380-7464

Top