Mother's Day Bracelet Project

Mother's Day Bracelet Project
B602

This project sponsored by:

Quantity of Items Needed

24 Swarovski Bicone 5328 4mm Aquamarine (AC4002)
24 Swarovski Bicone 5328 4mm Sapphire (AC4003)
24 Swarovski Bicone 5301 4mm Blue Zircon (AC4028)
42 Round Bead 3mm Sterling Silver (BD305)
6 Crimp Tube Seamless 2x2mm Sterling Silver (BD315)
6 Crimp Cover 3mm Sterling Silver (BD610)
27" Beadalon Wire .015" 15ft Silver Plated 19 Strand (BW215)
1 Three Strand Plunger Clasp 22x12mm Sterling Silver (CL735)
1 "Mom" Heart Charm - 13x16mm Sterling Silver (CM0072)
2 Jump Ring Round Open 4mm Sterling Silver (JR405)
1 Jump Ring Round Closed 5mm Sterling Silver (JR555)
1 Sterling Silver Rondell Dividers - 5 Hole (RD455)
1 Pkg. of India Seed Bead Silver Lined 6/0 Aqua (SB6223)
1 Pkg. of India Seed Bead Silver Lined 6/0 Blue (SB6226)
1 Pkg. of India Seed Bead Inside Color 6/0 Aqua (SB6333)

Instructions.

1) Take one 9" length of BW215

2) Start your beadwork.
1
Sterling Silver Seamless Round Beads (3mm)
1
Sterling Silver Seamless Crimp Tube (2x2mm)
1
Sterling Silver Seamless Round Beads (3mm)

3) Take one half of CL735 and the end of the beaded length of BW215. Thread the wire through one of the holes, then around and back through the three beads. Pull the wire until the beads are close to the clasp (don't make it too tight, as you want some movement when the strand is finished). Crimp BD315 with PL125. If there is any wire tail sticking out after threading it back through all the beads, cut that with PL495. Repeat with the two remaining lengths of BW215.

4) Now you're ready for the beading pattern. Each of the strands will start on a different section of the pattern. (You can have all the strands start on the same section if you like) Here are the sections (Completely finish each strand before threading the next)

Section #1
Section #2
Section #3
Section #4
4 -AC's (Bicones)
1 - Seed Bead
4 - Seed Beads
1 - AC (Bicone)
 
1 - AC (Bicone)
 
1 - Seed Bead
 
1 - Seed Bead
 
1 - AC (Bicone)
 
1 - AC (Bicone)
 
1 - Seed Bead

(In the picture, the Aqua strand started with section #4, and the Blue Zircon and Sapphire strands started with section #2) Place one BD305 between each section. After the sixth section, thread the wires through the 1st, 3rd, and 5th holes of RD455.

5) After stringing strand #1,
Start your beadwork.

1
Sterling Silver Seamless Round Beads (3mm)
1
Sterling Silver Seamless Crimp Tube (2x2mm)
1
Sterling Silver Seamless Round Beads (3mm)

6) Take the other half of CL735 and thread the end of BW215 through one the same number hole that you used on the other half of CL735. Then thread the wire around and back through the three beads. Pull until all the beads are close to the clasp (remember not snug). Crimp BD315. If there is any wire tail that is sticking out after threading the wire back through the three beads, cut it off with PL495.

7) Repeat the last step for the two remaining strands.

To Finish.
8) Take PL490 and PL491 and open the two JR405. Attach one to a hole on the end of CL735 and JR555. Close this jump ring. With the other open JR405, attach to CM0072 and JR555. Close this jump ring.
There are no reviews for this product!

Buy Project Components

Recently Viewed Items

Top