1) Take the 21" length of BW012 and thread on one BD363 and one half of CL1050. Take the end of this wire around and back through BD363. Pull the wire until the crimp tube is fairly snug against the clasp. Crimp with PL125. Cut off any excess wire with PL495.

2) Start your beadwork.
1 - Openwork Swirled Pewter Bead Cap (8mm/Gold)
5 - Fossil Coral Round Beads (8mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
4 - Fossil Coral Round Beads (8mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
3 - Fossil Coral Round Beads (8mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
2 - Fossil Coral Round Beads (8mm)
1 - Gold Filled Round Bead (Corrugated/3mm) 1 - Fossil Coral Round Beads (8mm)
1 - Openwork Swirled Pewter Bead Cap (8mm/Gold)
1 - Swarovski Round Beads (8mm/Crystal Golden Shadow)
1 - Openwork Swirled Pewter Bead Cap (8mm/Gold)
2 - Fossil Coral Round Beads (8mm)
1 - Openwork Swirled Pewter Bead Cap (8mm/Gold)
1 - Swarovski Round Beads (8mm/Crystal Golden Shadow)
1 - Openwork Swirled Pewter Bead Cap (8mm/Gold)
2 - Fossil Coral Round Beads (8mm)
1 - Openwork Swirled Pewter Bead Cap (8mm/Gold)
1 - Swarovski Round Beads (8mm/Crystal Golden Shadow)
1 - Openwork Swirled Pewter Bead Cap (8mm/Gold)
2 - Fossil Coral Round Beads (8mm)
1 - Gold Filled Round Bead (Corrugated/3mm)


Repeat this beadwork pattern working from the bottom, up to create the other half of the necklace. Thread on another BD363 and the other half of CL1050. Take the wire end around and back through the BD363. Pull snug and crimp with PL125.


3) Take the 1 1/2" length of BW012 and thread on:


4) Start your beadwork.
1 - Gold Filled Round Bead (Corrugated/3mm)
1 - Gold Filled Spacer Beads (Rondell/3mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
1 - Gold Filled Spacer Beads (Rondell/3mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
1 - Gold Filled Spacer Beads (Rondell/3mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
1 - Swarovski Seashell (40mm/Crystal Golden Shadow)
1 - Gold Filled Spacer Beads (Rondell/3mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
1 - Gold Filled Spacer Beads (Rondell/3mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
1 - Gold Filled Spacer Beads (Rondell/3mm)
1 - Gold Filled Round Bead (Corrugated/3mm)
1 - Gold Filled Spacer Beads (Rondell/3mm)
1 - Gold Filled Round Bead (Corrugated/3mm)


To Finish.
5) Thread on the last BD363. Thread each of the ends of this length of BW012 through the opposite ends of BD363. Done correctly, you'll have made a circle with the beads. Pull the ends of the wire tight and crimp with PL125.

6) To wear, simply thread the bail onto the necklace and rest it on the two corrugated beads in the center of the necklace. If you wanted to, you could make other bails, and wear different focal beads to match your wardrobe!